“Cold work banks mechanical work inside billions of dislocations, and annealing spends it via migrating boundaries—mastering temperature, strain rate, and orientation tames every grain.”Fundamentals of Materials Science · Ch. 12 · In Tribute to N. P. Goss & M. F. Ashby
Cold drawing dissipates ~90%–99% of work as heat while banking \(1\%\text{–}10\%\) in dislocations—how does annealing relieve stress and rebuild strain-free grains, and why must inline \(\mathrm{Cu}\) wire furnaces run at \(500\,^\circ\mathrm{C}\) for a few seconds?
Why does texture cause wavy “earing” on deep-drawn \(\mathrm{Al}\) cans, whereas car panels seek \(\{111\}\parallel\mathrm{ND}\) and transformer steels target \(\{110\}\langle 001\rangle\)? How do Lankford \(r\), hardening \(n\), and the Forming Limit Diagram (FLD) predict splits?
Why is rolling \(\mathrm{Pb}\) at \(25\,^\circ\mathrm{C}\) hot working while \(\mathrm{W}\) at \(1000\,^\circ\mathrm{C}\) is cold working? Why does hot-rolled \(\mathrm{Al}\) show a flat flow plateau while \(\mathrm{Cu}/\gamma\text{-Fe}\) show softening peaks, and how is \(\mathrm{Ti\text{–}6Al\text{–}4V}\) gas-blown into hollow fan blades?
Completing Ch. 12's processing loop: Stored Energy, Recovery, Recrystallization & Grain Growth \(\to\) \(\mathrm{Cu}\)-Wire Flash Annealing \(\to\) Textures, IF/Goss Steels & FLD \(\to\) Dynamic Recrystallization, Superplasticity & Ch. 12 Synthesis.
T₂ = 500 °C
| Core Module | Driving Force | Micro-Carrier & Scale | Governing Law / Criterion | Engineering Payoff |
|---|---|---|---|---|
| Geometry & Elasticity | Peach–Koehler \((\boldsymbol{\sigma}\cdot\boldsymbol{b})\times\boldsymbol{l}\) | Edge \(\boldsymbol{l}\perp\boldsymbol{b}\) · Screw \(\boldsymbol{l}\parallel\boldsymbol{b}\) · \(\boldsymbol{b}\) | Frank \(E\approx\alpha Gb^2\) · \(\tau b=T/R\) | Resolves \(10^4\times\) strength gap |
| Glide & Dissociation | Effective \((\tau-\tau_{\mathrm{c}})b\) | Glide/climb/cross-slip · \(d\propto 1/\gamma\) | \(\tau_{\mathrm{FR}}=Gb/L\) · Lomer–Cottrell lock | fcc cryo-tough vs. bcc DBTT |
| Yield & 4 Strengthenings | Schmid \(\tau_R=\sigma\cos\phi\cos\lambda\) | Forest \(\rho^{-1/2}\) · Orowan \(\lambda\) · pile-up \(n\tau\) | \(\sigma=M\tau_{\mathrm{c}}\) · \(\varepsilon_u=n\) · \(\sigma_y=\sigma_0+k_y d^{-1/2}\) | HSLA, BH/IF steel, T6 Al |
| Annealing & Texture | Stored energy \(P\approx\tfrac{1}{2}\rho Gb^2\) | Polygonization \(\to\) HAGB \(v=MP\) | \(T_{\mathrm{rx}}\approx 0.4T_{\mathrm{m}}\) · \(\bar{d}^2-\bar{d}_0^2=Kt\) · FLD | Flash Cu wire, IF & Goss steels |
| Hot Work & Superplast. | High-\(T\) flow + GB diffusion | DRV / DRX · Rachinger GBS | \(Z=\dot{\varepsilon}\mathrm{e}^{Q/RT}\) · \(\sigma=K\dot{\varepsilon}^m\;(m\gt 0.3)\) | TMCP steel, Ti–6Al–4V SPF/DB |
Inline \(\mathrm{Cu}\) wire dwells only seconds, so raising furnace \(T\) to \(500\,^\circ\mathrm{C}\) via \(t\propto\exp(Q/RT)\) completes recrystallization and restores \(100\%\text{ IACS}\); automotive IF steel cultivates \(\{111\}\parallel\mathrm{ND}\) \(\gamma\)-fiber for high Lankford \(r\) while \(\mathrm{MnS/AlN}\) secondary recrystallization builds Goss \(\{110\}\langle 001\rangle\) \(\mathrm{Fe\text{–}Si}\) to cut core loss \(70\%\).
Homologous \(T_{\mathrm{rx}}\) makes \(\mathrm{Pb}\) hot-worked at \(25\,^\circ\mathrm{C}\) and \(\mathrm{W}\) cold-worked at \(1000\,^\circ\mathrm{C}\); high-SFE \(\mathrm{Al}\) cross-slips into a flat DRV plateau, whereas sub-\(10\;\mu\text{m}\) \(\mathrm{Ti\text{–}6Al\text{–}4V}\) at \(927\,^\circ\mathrm{C}\) slides along grain boundaries with \(m\approx 0.5\) for rivet-free SPF/DB fan blades.
Next up — Final Chapter 13: Fracture & Failure of Materials — Griffith crack energy balance, fracture toughness \(K_{\mathrm{IC}}\), ductile-to-brittle transition, Paris fatigue crack growth & high-temperature creep.
1. Pure \(\mathrm{Al}\) melts at \(T_{\mathrm{m}}=933\text{ K}\). Using \(T_{\mathrm{rx}}\approx 0.4T_{\mathrm{m}}\), what is its \(T_{\mathrm{rx}}\)? Why does commercial \(\mathrm{Al}\) anneal much higher while inline \(\mathrm{Cu}\) wire runs at \(500\,^\circ\mathrm{C}\)?
\(0.4\times 933\approx 373\text{ K}\;(\approx 100\,^\circ\mathrm{C})\) in Kelvin. Trace solutes drag boundaries to raise commercial \(\mathrm{Al}\) \(T_{\mathrm{rx}}\), and seconds-scale flash annealing obeys \(t\propto\exp(Q/RT)\).
2. Regarding sheet textures, Lankford \(r\)-value, strain-hardening \(n\), and the Keeler–Goodwin Forming Limit Diagram (FLD), which statement is accurate?
\(\gamma\)-fiber \(\{111\}\parallel\mathrm{ND}\) resists thinning (\(r\approx 2.2\)); \(\mathrm{Fe\text{–}Si}\) uses secondary recrystallization for Goss \(\{110\}\langle 001\rangle\); plane strain \(\varepsilon_2=0\) is the split-prone \(\mathrm{FLC}_0\) trough.
3. Comparing hot-working dynamic recrystallization (DRX) and fine-grain structural superplasticity, which judgment is completely accurate?
High-SFE \(\mathrm{Al}\) undergoes flat DRV; high \(Z\) produces single-peak fine DRX grains; superplasticity relies on Rachinger GBS + diffusion where \(m\approx 0.5\) arrests necking.